Main Menu

Quartz Versus Limestone: Which sand is better in concrete overlays?

Concrete overlays’ strength comes from combining specific amounts of portland cement, sand, water and polymer. Sand type is an important component in decorative concrete and concrete overlays because overlays are typically applied thinner than standard concrete, yet still need to withstand the forces of foot and automobile traffic.

Research and experience with aggregates have taught us that some sand types can break down quickly with heavy use and traffic and can weaken the concrete over time.

All sands are not the same
Quartz sand is very hard and usually has no sharp or angular edges as it typi­cally comes from rivers and sand deposits where over the millennia the sharp or angular edges have been worn down.

Limestone, on the other hand, is a softer mineral so it doesn’t wear down into sand. It wears down into powder, which is why you don’t find deposits of limestone sand. Limestone powder or derivatives of it are used to make powdered portland cement. Limestone sand, which is used in some decorative concrete, is created by crushing limestone rocks to make sand. Limestone sand is soft enough that the angular edges of the grains can be easily crushed, broken and turned to powder.

You can test this yourself by rubbing crushed limestone sand together in your bare hands and watch as it starts to create powder. Concrete overlays with softer sands show wear faster and have more trouble supporting foot traffic, chairs, tables and vehicles because they scuff, scratch, chip and spall. Some even crumble and fail. It’s true that limestone sand in repair mortar has worked great for centuries to fix columns, sculptures and items with no traffic, and it can work well as larger aggregate in standard concrete.

However, if your aggregate or sand fails, it can cause the other ingredients to also fail. This is due to the voids created when the softer sands turn to powder and break the physical bond between all the other ingredients and the substrate.

As a manufacturer, we select ingredients based on many factors, and one of them is the Mohs hardness scale (see chart). This scale is designed to help people around the world choose the best mineral (sand) for their specific use.

According to the Mohs scale (https://www.concretedecor.net/decorativeconcretearticles/vol-13-no-4-mayjune-2013/make-tooling-choices-easier-with-the-mohs-hardness-test-kit/), you can see why quartz is used whenever possible when making concrete, decorative concrete and concrete overlays. It’s harder, will stand up to more abuse and lasts longer.

To be fair, concrete — like natural stone — breaks down over time, but weaker aggregate or sand can break down faster.

Picture 1: Stone Edge Surfaces Stamp mix

Picture 1: Stone Edge Surfaces Stamp mix

Picture 2: Stone Edge Surfaces Wall mix
Picture 2: Stone Edge Surfaces Wall mix

Achieving a realistic look
Even if you know the difference when comparing quartz sand and limestone sand, what we’ve found is that a realistic “look” is created by a combination of all the ingredients used in a concrete overlay mix. Once the sand is mixed with the concrete ingredients, you don’t see the sand as anything more than part of the mix. It’s not discernible once it has been immersed, coated and covered with the gray or white portland cement and additive mixture in the dry concrete overlay mix.

Pictures 1 and 2 show four different concrete overlay mixes in powder form right out of the bag. Picture 3 shows a concrete overlay mix applied to a wall and stamped but not colored. Picture 4 shows the same wall and concrete mix colored and finished.

Sand plays a minor part in the overall realistic look. The other factors that add to the realism are the type of polymer or acrylic used in the mix, the sealers, pigments, dyes, integral colors and skill level.

You must factor in the skill of the applying contractor because a skilled contractor can make almost any mix look good, while an unskilled contractor can ruin the look of even the best mix. There are many factors that contribute to a realistic look. Sand is a main contributing factor for strength and form.

Picture 3: Seen here is a concrete overlay mix applied to a wall and stamped but not colored.

Picture 3: Seen here is a concrete overlay mix applied to a wall and stamped but not colored.

Picture 4: Here’s the same wall that’s been colored and finished.

Picture 4: Here’s the same wall that’s been colored and finished.
 

Which sand is used most often?
Most industries seem to prefer quartz over limestone sand. Due to its unique properties, quartz sand is predominantly used throughout the concrete, paint and adhesive industries.

Quartz sand helps paint and other products be more chemical resistant. Naturally acid- and wear-resistant because of its hardness and ability to take scrubbing, it improves durability and flowability of paint.

Because of its reinforcement qualities, quartz sand is used in industrial rubber. It’s also used in tire linings as it offers superior adhesion, tear resistance and heat-aging properties. When added to adhesives for tiles, quartz sand improves tensile strength and impact resistance.

Based on our own experience with aggregates and the information and research available to us, we believe quartz sand is the more durable ingredient to use in a concrete overlay mix that’s going to see foot or vehicle traffic. For long-term durability and stability in general for both residential and commercial projects, quartz sand is the way to go.

Hardness Mineral Observations of Mineral
1 Talc Very easily scratched by fingernail.
2 Gypsum Can be scratched by fingernail.
3 Limestone, Calcite Very easily scratched with a knife and/or a copper coin. This is where most marbles, limestones and travertines rate.
4 Flourite Can be scratched by a knife.
5 Apatile A knife has difficulty scratching this mineral; glass is rated in this hardness.
6 Orthoclase

Cannot be scratched with a knife. This mineral can scratch glass with some difficulty.

7 Quartz

Can scratch glass easily. This is where most granites are rated in terms of hardness.

8 Topaz

Can scratch glass very easily.

9 Corundum

Can cut glass.

10 Diamond Can scratch virtually anything; is commonly used to cut glass and stone.

 

Bruce Grogg is president of Stone Edge Surfaces in Mesa, Arizona, a division of Turley International Resources LLC, one of the largest manufacturers of concrete overlay products in the U.S. Grogg has more than 20 years of domestic and international manufacturing experience in the custom product and concrete overlay industries. His accolades include being a past voting member for the International Code Council’s ISPSC code development committee, helping author two current ICC codes and leading the Pool & Hot Tub Alliance’s Government Relations Water Saving Coalition. Grogg can be reached at [email protected] or (844) 786-6333
.

  Advertisements












Top