Main Menu

Advantages of Water-based Acrylic Concrete Sealers

In the 30-odd years I’ve been in the concrete industry, first as a contractor and now as a retailer, I’ve heard time and again that water-based acrylic sealers can’t compare to solvent-based acrylics. I don’t know who came up with this idea or how it became so universally accepted. Maybe it was true “back in the day,” however, based upon my own observations and experimentation, I no longer subscribe to that train of thought. In fact, I believe using water-based acrylics can be beneficial in many cases.

After four years of weathering, here is a side-by-side comparison of an area with a water-based brown acrylic sealer on the left and what little, if any, solvent-based brown acrylic sealer is left on the right. Photos courtesy of Steve VandeWater
After four years of weathering, here is a side-by-side comparison of an area with a water-based brown acrylic sealer on the left and what little, if any, solvent-based brown acrylic sealer is left on the right. Photos courtesy of Steve VandeWater

The turning point
My pessimistic attitude toward water-based sealers began to change about five years ago. I had recently quit contracting and had taken a new job selling decorative concrete supplies. While sampling sealers from a number of manufacturers, I tested both solvent-based acrylics and water-based acrylics on stamped and colored concrete.

One day I stripped the sealer off a very small 1-by-1-foot section so I could test some acid stain. In the past, if I needed to strip a small bit of acrylic sealer, I simply used xylol and a rag. That was my plan this time, too.

I applied the xylol to some water-based acrylic sealer and, to my surprise, nothing happened. I applied more, and really let it puddle and sit for a while. I wiped off the still-wet xylol with a rag and the sealer remained unaffected. I applied more xylol and vigorously scrubbed the area with a stiff brush and a terry cloth. After about 10 to 15 minutes of constant work, I had only stripped an area about the size of a quarter dollar. I quickly concluded that if water-based sealer was tough enough to withstand that kind of abuse, it would do equally well in normal weather.

textured floor with light strip - Seen here is a water-based acrylic sealer with a satin finish on textured concrete.
Seen here is a water-based acrylic sealer with a satin finish on textured concrete.

New regulations, new carriers
Not long after this experience, I got word that Indiana was adopting new regulations regarding solvent-based sealers. Due to changes in VOC laws, xylol would no longer be a component. Instead, acetone and its derivatives would be the new carriers. Unlike xylol, these solvents are notorious for drying extremely quickly. Many dry much too quickly to be used effectively. With that in mind, I knew my customers would have to learn a whole new way of doing things. I began to experiment with VOC-compliant sealers to see what was in store for my contractors.

I found rolling these fast-drying sealers was problematic, especially in hot weather. Often, the sealer would dry so quickly that it would begin to “cobweb” from the roller. Fine strands of sealer would float around in the air like wisps of cotton candy.

Even when the application appeared to go well, there were often well-defined roller marks after the sealer dried. These were apparently caused by a double coat of sealer between roller passes. The solvent would flash off so quickly that the sealer could not melt into itself as it was being rolled. Streaking was even more prevalent when using brown-tinted concrete sealer on exposed aggregate surfaces.

In addition to the streaking issue, bubbles would often times form in the sealer. These could either be large bubbles, about an inch in diameter, or thousands of tiny closely spaced bubbles which gave the impression that the sealer had blushed (whitened). There were also times when tiny bubbles were invisible, but became very noticeable when they crackled loudly underfoot. Sometimes, there appeared to be no problems at all, but three weeks later bubbles would form! Clearly, there had to be a solution.

A side-by-side test
About that time, I asked a sealer manufacturer to formulate a dark brown-tinted concrete water-based sealer for me to test. I poured a small sample of exposed pea gravel concrete. On one half of the sample, I applied brown-tinted concrete solvent-based acrylic sealer. On the other half, I applied the brown-tinted concrete water-based acrylic sealer. Initially, both sides looked good. They were both nice and shiny, but I preferred the darker pigment that had been added to the special water-based sealer.

I set this sample outside my store, directly under a downspout. Each time it rains, water beats down upon it. In the past four years, the solvent-based sealer has been completely weathered away. On the other hand, the water-based sealer still appears nearly the same as it did when applied. It has lost a bit of gloss, but the rich color and slight sheen are still intact.

Pros and cons
Based on my observations, I have begun advocating the use of water-based acrylic sealers over solvent-based ones for all types of concrete. Benefits of water-based sealers include:

  • They don’t release harmful vapors into the atmosphere.
  • They are far safer for the worker to apply, especially indoors.
  • They are easier and cheaper to apply because they can be sprayed on with a cheap plastic garden sprayer and don’t flash dry during warm weather.
  • They eliminate or reduce most sealer problems including bubbling and roller marks.
  • They are often more durable.
  • They are available in high-gloss or matte finishes.
  • They don’t darken the surface nearly as much as solvent-based sealers, so the surface looks much more natural. To some, that’s an advantage when installing decorative concrete.
  • Water-based acrylic cure-and-seals work just as well as solvent-based ones for curing plain concrete — again without darkening the surface.

In fairness, water-based sealers do have some drawbacks. They include:

  • Water-based sealers are very difficult to remove if a problem should occur.
  • They don’t work well when applied at temperatures below 50 degrees Fahrenheit.
  • Water-based sealers will freeze and become unusable much more easily than solvent-based acrylics.
  • They do not provide the darkening effect that some customers prefer, especially on decorative concrete.
  • When exposed to long periods of wet weather, they may rewet and appear milky. Typically, though, when the surface dries, the sealer once again becomes clear.

Taking all things into consideration, it may make your life easier if you try water-based sealer on your next project. Your employees, as well as the rest of the planet, will benefit as well.

Steve VandeWater, a former decorative concrete contractor, is the creator of the Indiana Decorative Concrete Network website www.indecorativeconcrete.com. He currently manages The Concrete Store at Sagamore Ready Mix in Fishers, Indiana.

Related Content

Vegas Artisan Puts Fresh Concrete Stamp on Venerable Casino

Stamped concrete walkway in Las VegasWith its 1,149-foot “space needle,” the Stratosphere Casino, Hotel & Tower is a Las Vegas landmark. When its owners, American Casino & Entertainment Properties LLC, remodeled it inside and out in fall 2012, they asked Owen Ondrisko, of Stampco Concrete, Henderson, Nevada, to design landscaping and concrete for the approaches to the building.

How Can You Minimize Sealer Slipperiness on Concrete?

Sealing a concrete patioUsing grit additives has become the most common method for reducing slipperiness when sealing decorative concrete flatwork on exterior walking surfaces. The grit additives are mixed into the sealer, then the gritty sealer is applied to the concrete. However, in this situation the weather was too cold to reseal the concrete. So another method needs to be used until springtime arrives and temperatures rise.

Prepping Your Finished Concrete Surface for a Sealer

How to fix cloudy sealer on concrete surfaces.

Surface preparation is a commonly used term in the decorative concrete industry. An argument can be made that it might even just be the most used term in the industry. We hear or read about it most often when dealing with overlays and stains. Grind, scarify, acid etch, etc.

  Advertisements









Top